How much is concrete per yard in Kansas City?

How much is concrete per yard in Kansas City?

Concrete Cost Per Yard According to the NRMCA, concrete costs $108 per cubic yard on average. With concrete delivery and pouring, most pay $119 to $147 per cubic yard depending on the PSI of the cement. A full 10-yard truckload with delivery costs $1,169 to $1,444, which is enough to pour a 20×24 driveway.

How much does a 1200 sq ft concrete slab cost?

A typical concrete slab will cost between $113 and $126 per cubic yard (27 cubic feet) or $5.35 to $6.17 per square foot on average….Concrete Slab Prices By Size.

Slab Size Square Feet Average Cost Installed
30×40 1200 $7,404
40×60 2400 $14,808

Is it cheaper to lay concrete or pavers?

As far as installation costs and concrete costs go, poured concrete is technically the most affordable per square foot. However, even though the upfront cost of pavers is higher, concrete pavers offer greater value and durability than poured concrete and stamped concrete.

Does paver patio add value to home?

When homeowners invest in a paver patio, they can expect extreme durability, minimal maintenance and — you guessed it — added value to their home. According to Inman, a leading real estate news source, patio additions to homes (when done properly) can deliver a return on investment of anywhere between 30% to 60%.

Is patio worth the money?

That said, it’s estimated that patios can recover up to $6,525 of the cost to build, which is an ROI of just over 100%. A better option for most homeowners, however, would be to refinish or repair an existing patio, as repair estimates average around $1,300. This can provide an ROI of nearly 500%.

Are pavers worth the money?

Pavers have a higher resale value because of their beauty and versatility. Concrete slabs are generally more common, but over time, pavers will net you more value because concrete is expensive to replace.

Is it cheaper to make your own pavers?

Total cost will be in favor of DIY as of the brake-even point of the molds and concrete, and getting nothing but cheaper per unit the more you make (assuming you never break the molds).

How do I stop my pavers from sinking?

Compacting causes the stones to form a tight bond with the bedding layer, which reduces the chance of your pavers sinking again. Sweep joint sand into the joints between the pavers. Do this by pouring a pile of sand on your hardscape and sweep it over the stones until your joints can’t hold any more sand.

Will sand keep pavers from sinking?

Once all the paver stones are in place, tamp them to make sure that they are all compacted to form a tight bond within your bedding layer. This will prevent your pavers from sinking again. You should also pour a pile of sand on the surface and sweep it over the stones to fill up any spaces within the joints.

What causes paving to sink?

One of the main reasons why your block paving sunk is because the drive was not done properly. In most cases, the reason is ground preparation. Your company probably didn’t dig enough out. To get a good block paving, the company setting your driveway needs to dig out down to good solid ground.

How much does it cost to fix sunken pavers?

Average Costs to Repair a Patio

Repair Cost
Filling in Cracks $5 – $150 per project
Replacing Uneven, Sunken Concrete $5 – $15 per square foot
Cost of leveling with Mudjacking or Slabjacking $2 – $5 per square foot
Lifting or Raising Brick & Stone Pavers $0.50 – $3 per brick/paver

Should you put plastic under pavers?

Do not place plastic under any paving application Plastic will entrap water, potentially causing other problems. In most cases, seeds start from the top of the cracks and work their roots down.

How do you fix sunken driveway pavers?

This is to stop you taking up the whole block pavers.

  1. Lift & remove the area of uneven block paving.
  2. Clean the paving you have removed.
  3. Level up the uneven area with grit sand.
  4. Re-lay the block pavers.
  5. Compact the relaid paving.
  6. Apply kiln dried sand.